Prepare Maintenance Visit

General

This process handles the preparation for a heavy maintenance visit. Preparing a maintenance visit allows:

Benefits

Following are some of the benefits provided by the capabilities within the Prepare Maintenance Visit process:

Define Maintenance Visit

For most service orientated businesses, a rough idea of the workload for the business over the year is a good indication of how effective the business is or can be operated. To facilitate this, it is possible to enter a number of maintenance slots which represent potential opportunities for when an asset could pass through the maintenance facility for a variety of maintenance activities. During the initial phase of this planning, the facility manager will review the capacity of the facility in terms of which assets can be supported (size-wise and according to the approved capability of the facility), the available resource hours, any facility downtime (maintenance, shutdown etc) and the target budget for the year. The registration of maintenance slots allow facility planners to register potential maintenance visits long before the actual visit is due to take place. This improves the planning of the throughput through a facility.

Once the manager has identified these slots, further negotiation between the service provider and any operators can occur. Often maintenance facility managers will also reserve slots for opportunistic visit requirements, specifically in the Defense domain, where heavy maintenance providers also support repair activities for damaged assets. Opportunistic visits could also occur in Civil Aviation domains where operators have the option of using various service providers which have the approved capability to support the asset, as such facility managers also bear these requirements in mind when planning the load within their facilities.

In many instances when the visit is being negotiated between the service provider and operator, a broad understanding of the basic type of maintenance event which will be required to be performed when the asset enters the maintenance facility is known, for instance, D-Check.

Plan Maintenance Visit

As the planning process continues to firm-up, confirmation of the real maintenance requirements of the asset are confirmed and agreed between the service provider and operator. This process relies on a vast quantity of information being available in IFS/Fleet and Asset Management before the full contents of the visit can be firmed up. If the asset is not fully maintained using IFS/Fleet and Asset Management capabilities, which could occur in instances where the service provider uses IFS Cloud but the operator uses their own forward/at asset maintenance application, a vast quantity of information must be available in IFS/Fleet and Asset Management before the full contents of the visit can be firmed up. However, even if the service provider and the operator share information, in the same instance of IFS Cloud, it may be required of the service provider to add and enhance the contents of details pertaining to event codes, task cards and configuration.

As a minimum the following information needs to be created via IFS/Fleet and Asset Management:

The Plan Maintenance Visit process therefore covers the relating of various maintenance event codes to the instance of the maintenance visit. As such, interval maintenance, modifications, serial faults, deferred faults and LLP replacements that are agreed to be included as part of the maintenance visit are added to the maintenance order which represents the instance of the visit. This could either be a maintenance slot which is firmed up with additional information such as the serial number and event codes which are applicable or a new maintenance order which could represent an opportunistic maintenance visit.

Once all event codes and task cards have been added to the maintenance order, the planner will arrange the contents of the visit to attempt to ensure the best planning throughput through the maintenance facility. The planner will review the ELS Gantt, and create dependencies between various event nodes and task cards (resulting in a network of events) by using various inputs from:

The planner will also review any task cards which have not been grouped effectively into the most appropriate ELO (Execution Logic Order) node in the visit structure and move these to the most valid ELO.

Once the planners of a visit are satisfied that the plan is accurate and representative of the scope of the maintenance visit they will:

Maintenance Visit Inspection

Often service providers and operators agree that a pre-visit inspection can physically be performed against the asset before it is scheduled to arrive at the maintenance facility. The objective of these inspection visit(s) is to gain further confirmation of the validity of the agreed content of the visit and also gain better understanding of the basic maintenance condition of the asset before it arrives at the service provider. As part of this process, additional events can be negotiated for inclusion, specifically where AD (airworthiness directive) and/or SB (service bulletin) and so on and so forth have been published but not incorporated against the asset. It is also possible to exclude some event from the scope especially in instances where interval maintenance of components and such were agreed during the planning phase of the visit, but where component changes have occurred between the original scope and the actual scope of contents for the visit.

Maintenance Visit Induction

Once an asset arrives at the service provider's facility it needs to be inducted. This potentially includes:

Once the operational data for an object is updated, interval maintenance, modification events and LLP replacements are calculated. This could in turn require the addition of event codes to the maintenance visit to ensure that the reliability of the asset can be maintained.